Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

Recent progress of green sorbents-based technologies for low concentration CO2 capture

The increased concentration of CO₂ due to continuous breathing and no discharge of human beings in the manned closed space, like spacecraft and submarines, can be a threat to health and safety. Effective removal of low concentration CO₂ from the manned closed space is essential to meet the requirements of long-term space or deep-sea exploration, which is an international frontier and trend. Ionic liquids (ILs), as a widespread and green solvent, already showed its excellent performance on CO₂ capture and absorption, indicating its potential application in low concentration CO₂ capture. In this review, we first summarized the current methods and strategies for direct capture from low concentration CO₂ in both the atmosphere and manned closed spaces. Then, the multi-scale simulation methods of CO₂ capture by ionic liquids are described in detail, including screening ionic liquids by COSMO-RS methods, capture mechanism by density functional theory and molecular dynamics simulation, and absorption process by computational fluid dynamics simulation. Lastly, some typical IL-based green technologies for low concentration CO₂ capture, such as functionalized ILs, co-solvent systems with ILs, and supported materials based on ILs, are introduced, and analyzed the subtle possibility in manned closed spaces. Finally, we look forward to the technology and development of low concentration CO₂ capture, which can meet the needs of human survival in closed space and proposed that supported materials with ionic liquids have great advantages and infinite possibilities in the vital area.     

重轨矫直速度对矫后残余应力的影响分析

针对矫直速度对重轨矫后残余应力的影响进行研究,利用Pro/E建立60kg·m-1重轨九辊水平矫直模型,采用ANSYS Workbench对重轨矫直过程进行有限元数值模拟,通过现场矫直规程对采用现场矫直速度以及假定矫直速度得到的重轨矫后残余应力进行分析比较,得出了在其余条件不变的情况下重轨的矫直速度在1.4~1.6m·s-1的范围内其轨底矫后纵向残余拉应力小于250MPa,且残余应力分布合理,满足矫直要求,相比于现场采用的1.2m·s-1的矫直速度其生产效率最大能够提高16.7%~33.3%。     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

内插法在相关干涉仪测向体制中的应用

测向误差的减小一直以来都是无线电测向精度提高的一个难点,对于不同的测向体制所采用的减小测向误差的方法都不尽相同。本文主要介绍的是相关干涉仪测向体制的基本原理以及通过内插法的应用来减小测向误差的方法。     

Analysis of Phytochemical Composition of Camellia oleifera Oil and Evaluation of its Anti-Inflammatory Effect in Lipopolysaccharide-Stimulated RAW 264.7 Macrophages

In China, Camellia oleifera oil (COO) is not only a common edible oil but also a traditional remedy widely applied to ameliorate a variety of illnesses associated with inflammation, such as mouth ulcers, thrush, eczema, etc. However, there has been a lack of relevant biological research on the anti-inflammatory capacity of COO, and the specific bioactive lipid phytochemicals contributing to the anti-inflammatory effect need further research. In this study, the RAW 264.7 macrophages model was used to investigate the anti-inflammatory capacity of COO. Our data showed that 33–200 μg/mL COO markedly inhibited the lipopolysaccharide lipopolysaccharide (LPS)-stimulated nitric oxide (NO.) secretion via the suppression of Nos2 and Cox-2 expression. The enzyme immunoassay confirmed that COO also exhibited a strong suppressive effect on the expression of proinflammatory cytokines such as Tnf-α and Il-6. To further explore the correlation between the anti-inflammatory effects and the lipid phytochemicals in COO, 10 samples were collected and screened for their chemical compositions. It was interestingly demonstrated that the polyphenol extracts of COO play a vital role in its anti-inflammatory properties. In addition, an oil-in-water (O/W) emulsion-based system was also developed to deliver the liposoluble COO into the cells, and the feasibility of this system was confirmed. Our research confirms the anti-inflammatory potential of COO and highlights that the main functional ingredient is polyphenol extracts. This may provide a scientific basis for the comprehensive utilization and development of COO and related functional foods.     

古建筑木结构透榫节点力学模型研究

为研究古建筑木结构透榫节点的M-θ力学模型，在分析透榫节点构造特征与受力机理的基础上，建立其数值模型，用透榫节点的试验数据验证了该数值模型的正确性，并分析了节点缝隙、木材横纹弹性模量和大榫头长度对透榫节点受弯承载力的影响。根据受力分析结果，建立以弹性点、屈服点与极限点为特征点的三折线多参数M-θ力学模型，其结果与多数的试验结果基本吻合，并将该力学模型应用于木构架的受力分析。研究结果表明：透榫节点的滞回耗能能力强，节点的变形主要集中在榫头处。当榫头与卯口之间的缝隙增大时，节点的受弯承载力降低。随木材横纹弹性模量的提高和大榫头长度的增加，节点的受弯承载力有一定提高。文章建立的M-θ力学模型能较好反映透榫节点的受力过程，适用于木构架的受力分析，其荷载 位移骨架曲线与试验结果基本吻合。研究成果可为古建筑木结构的维修与保护提供参考。     

Fine-tuned,molecular-composite,organosilica membranes for highly efficient propylene/propane separation via suitable pore size

Fine-tuned, molecular-composite, organosilica membranes were fabricated via the co-condensation of organosilica precursors bis(triethoxysilyl)acetylene (BTESA) and bis(triethoxysilyl)benzene (BTESB). Fourier transform infrared and UV–vis spectra confirmed the co-condensation behaviors of BTESA and BTESB. The evolution of the network structure indicated that the incorporated BTESB decreased the membrane pore size, which was determined by a modified gas translation model according to the steric effect of the phenyl groups. The incorporation of BTESB to BTESA finely tuned the membrane structure and endowed the resultant composite membrane with improved separation properties. The BTESAB 9:1 membrane (molar ratio of BTESA/BTESB was 9:1) exhibited high C₃H₆ permeance at 4.5 × 10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ and a C₃H₆/C₃H₈ permeance ratio of 33 at 50°C. One of the most important developments of this study involved clearly defining the relationship between membrane pore size and C₃H₆/C₃H₈ separation performance for organosilica membranes in single and binary separation systems.